News

Shooting of a Marketing Film in England

September 21, 2023

Bridge Beam Manufacturing For HS2: A Behind-the-Scenes Look In the town of Melton Mowbray, a joint venture is taking place at the FTB facility. This…

Project

Customer Service: The Art of Giving People More than They Expect

April 17, 2023

Visiting a good restaurant quickly loses its appeal if the service is incompetent and unmotivated or even noticeably absent. But of course, bad service is…

Project

Accelerated Concrete Curing using Radiant Heat

April 17, 2023

Growth in metropolitan areas and their inhabitants’ demand for rapid transportation present many of the world's major cities with extensive infrastructural challenges. Tunnels, constructed with…

Project

A Green Way to Cure Concrete

April 17, 2023

Climate change, sustainability, global warming and CO2 are on people's minds all over the world, regardless of the industry, and this will not change in…

Project

The Müller-Steinag Group increases production capacity with a new concrete curing system

December 13, 2021

(Article in CPI – Concrete Plant International – 6 | 2021) At the Rickenbach site, the Müller-Steinag Group operates two self-sufficient concrete block lines in…

Project

Kann GmbH invests in the future with a modern curing chamber

December 13, 2021

(Article in CPI – Concrete Plant International – 5 | 2021) Kann GmbH Baustoffwerke, with its headquarters in Bendorf-Mühlhofen and a total of 20 other…

Project

Turn-Key Installation for a brand new Quadrix® System

July 7, 2021

Last week, Kraft Curing began another turn-key installation of a large project for a manufacturer of concrete hardscape products (pavers, curbs, and blocks) in Germany.…

Project

The perfect accompaniment to a carousel concrete wall production plant.

January 27, 2021

One of India's largest precast property developers is now adding three additional Convect-Air systems to their already extensive catalogue of Kraft Equipment. The three sets…

Project

And off we go to India!

November 25, 2020

This 2 year old, reconditioned Vapor Generator will now embark on the long journey to it's new owner in India, simply taking its home with…

Project

Prioritized Coordination of Engineering and Production Departments to Slash Delivery Time

November 20, 2020

The Kraft Curing team quickly rolled up their sleeves after receiving this rush order from the USA for a 94% efficient 1400 kWh ThermalCure hydronic…

Project

Installation of a true rarity!

November 16, 2020

The QUADRIX ULTRA at Tobermore Concrete Productions Ltd. in the UK is completely finished now and will in the future accelerate the hardening process, thus…

Project

Everything shines new!

November 13, 2020

This valued customer in Poland just took delivery a complete QUADRIX® curing package. This includes our QUADRIX® air-heating and circulation unit, AutoCure® curing controls, AutoFog®…

Technology

Take Control from Anywhere – With Access Anywhere!

May 26, 2020

Enhance your AutoCure® control with Access Anywhere and become mobile! The ACCESS ANYWHERE interface connects your concrete curing facility with up-to-date communication devices including PCs, tablets…

Project

A long-lasting and successful partnership

February 1, 2020

Kilsaran International, a family-owned Irish company based near Dublin in Piercetown, County Meath, has been an international byword for innovative concrete and asphalt products for…

Technology

Vapor is better than Steam

January 14, 2020

Why does a vapor generator have no flue?How is vapor actually produced without boiling water?Why is vapor better for your concrete - and your bank…

Company News

Sponsoring for special school

December 3, 2019

KRAFT contributed to school sports aid 2019 Together with other local companies, we have gladly supported our local Maximilian-Kolbe-School in Löningen with the procurement of…

Company News

OPENING OF NEW KRAFT BUILDING IN LINDERN

November 15, 2019

On Friday, November 15, 2019, the new production hall with office building was officially opened at KRAFT CURING in Lindern at a ceremony attended by…

Technology

Temperature difference in the chamber – the enemy of quality

September 3, 2019

Different climate zones in curing chambers are more the norm than the exception. They cause color differences and problems in the strength of concrete products.…

Technology

Ecological layer securement and surface protection with biodegradable material

July 8, 2019

Modern architecture places ever higher demands on the production of terrace slabs and concrete paving stones. The storage and transport of such high-quality slabs is…

Technology

Thermal images help assessing insulation issues in curing chambers

May 2, 2019

Due to its lower capital cost, low energy and maintenance costs and highly positive impact on the consistency of concrete color, strength and durability, the…

Technology

Newly developed shelf design provides for a durable connection and secure operation

March 4, 2019

Investing in a curing rack means relying on years and years of uninterrupted service in order to achieve the neccessary return-on-investment. Every breakdown, any damage…

Technology

“Made in Germany” curing rack with computer-optimised design and integrated curing climate control

May 18, 2018

“Concrete should be cured, not dried.” Kraft, located in Lindern in Lower Saxony, have consistently followed this principle for over 25 years and committed their…

General

Benefits of the innovative QUADRIX® Curing Technology

October 1, 2017

For producers of concrete pavers and blocks, switching to a Single Atmsophere Curing Chamber (Big Room) offer substantial benefits. A factual, indepth and informative dissertation,…

Project

Heating Concrete in the Desert

April 1, 2017

In 2015, one of the leading producers of precast concrete products in the United Arab Emirates, Hi-Tech Concrete Products, installed a ThermalCure® Accelerated Concrete Curing…

Project

Accelerated Concrete Tunnel Segment Curing for the Albvorland Tunnel

March 15, 2017

For the Stuttgart-Ulm railway project a new high-speed section is being built from Wendlingen (Neckar) to Ulm alongside the A8 motorway. The new section will…

General

Concrete pavers with triple protection

January 1, 2017

Gerwing revised and optimized numerous processes in their concrete block paving production in order to achieve the desired result, which is now marketed under the…

Project

Heinrich & Bock rely on controlled concrete curing

June 1, 2016

KRAFT’s challenge in the Wittenheim plant, which Heinrich & Bock had owned since 1998, was to create a consistent day-to-day climate in the large volume…

Project

Low-emissions curing system offers significant cost savings

April 1, 2016

In April 2013, Sovereign Concrete of Australia contacted KRAFT CURING SYSTEMS to replace an outdated boiler system. In compliance with local standards and Sovereign’s unique…

Project

Quality increase and cost reduction by controlled concrete curing conditions

February 1, 2016

The goal of every producer must be to produce the lowest cost product, available within 24 hours, with consistent and bright colors, without efflorescence and…

Project

Accelerated concrete hardening system ensures consistent climatic conditions in a single atmosphere chamber throughout the year

January 1, 2016

"The impossible has become possible – now we can produce in three shifts." Those were the words of the regional director for production, Mr. Paweł…

Project

CityStoneDesign: Reaching higher quality standards through curing

May 1, 2015

“With CityStoneDesign, we emphasize new exciting products as well as product quality through extraordinary aesthetics paired with technological excellence and functionality”, says Peter Bozek, CityStoneDesign…

Project

Van Dyk Stene invests in fully automated concrete products plant with integrated curing system

April 1, 2015

The newly commissioned Van Dyk Stene concrete products plant in Vredenburg in the Western Cape is saving the company 30% on its total cement input…

Project

Kilsaran Group invests in new curing technology

March 1, 2015

To keep up with market demand for high quality products, Kilsaran Group (located in Dublin, Ireland) opted for KRAFT's Quadrix® Accelerated Concrete Curing Systems to…

Project

Remote overnight concrete curing for bridge elements

January 1, 2015

For the densely populated state of New York the Tappan Zee Bridge, crossing the Hudson river north of the city of New York constitutes a…

Project

Concrete curing system installed during operation

December 1, 2014

On the occasion of the anniversary, the company Bruk Bet expanded their paving block production facility at the location in Kielce by a concrete curing…

Technology

Direct-fired vapor for concrete curing

July 1, 2014

Vapor is used in the precast concrete industry for the accelerated curing of precast products including concrete pipe, prestressed structural concrete, concrete block, ornamentel concrete,…

Project

Bruk Bet relies on proven concrete curing quality on its anniversary

June 1, 2014

Bruk Bet is one of the largest Polish manufacturers of decorative concrete blocks and paving stones. The family-run company with several production locations in southeast…

Project

The Evergreen Line Tunnel Project in Vancouver, Canada

March 1, 2014

In late 2013, Vancouver, BC topped the list of most congested cities in North America. On average, peak hour travel time was 36% longer than…

Project

Quadrix® concrete curing systems integrated into 7 existing concrete block paving plants

January 1, 2014

In the early summer of 2013 a well-known concrete block manufacturer from Central Europe ordered seven Quadrix® II concrete curing systems from the German company…

Project

Highly flexible production of precast elements for housing and industrial applications

August 1, 2011

Grupo Cementos de Chihuahua (GCC), Mexico has successfully improved the quality and resistance of their manufactured concrete precast panels. Through their new, customer specific engineered…

Project

Exceeding expectations

April 1, 2011

“Calstar approached KRAFT because they bring extensive knowledge in curing of a wide range of concrete construction products, including those containing recycled materials, exactly the…

Project

New curing system for Western Materials, USA

March 1, 2009

For over sixty years, Western Materials has been dedicated to providing their customers with quality products including concrete architectural and hardscape products that they manufacture…

Project

Energy savings

August 1, 2007

Knife River Corporation recently received the MDU Resources Group, Inc. Einstein Award. These awards are bestowed upon employees of MDU Resources for their process improvement…

Project

Concrete curing environment for architectural and landscaping products at Northfield Block

April 1, 2007

Northfield Block, an Oldcastle company with locations throughout Illinois, has been in business since 1949. It has built a reputation on aesthetically pleasing and quality…

Project

Curing of concrete roofing tiles (Hungary)

February 1, 2007

Hungarian company Mediterran Kft. decided to upgrade the aftertreatment system of its main plant at Bóly in the heart of Hungary to a KRAFT Vapor…

Project

GCC moves to the technological forefront in the construction materials industry

January 1, 2007

When Grupo Cementos Chihuahua, GCC, of Mexico decided to build a new block, paver and architectural products production facility in Juarez, Mexico the decision was…

Project

Whisper-steam lets precast systems’ neighbours smile

January 1, 2000

Precast Systems Incorporated/Caledonia Concrete Cooperation has recently opened up their new production facility in Allentown, New Jersey, USA. Since the formation of the company in…

Search

News

Recent Posts

Archiv

About company

Recent News

Contact info

Newsletter